How-to · Reverse Osmosis Systems
How to Clean a Reverse Osmosis Water Filter
To clean a reverse osmosis water filter, shut off the water supply, unplug the system if it uses power, and open the faucet to release pressure. Remove each filter housing, wash the housings with mild dish soap and water, and rinse them. Replace any cartridge that looks grey or worn, refit the housings, and flush the system as the maker's manual says.
Shut off the water and power
Close the feed valve that supplies the system and unplug the unit if it uses corded power. Open the faucet and let the water run until the flow stops, which releases the pressure in the lines. Keep the maker's manual nearby so you can follow its order for your model. Place a towel under the housings to catch the water that drains out.
Remove the filter housings
Unscrew each filter housing one at a time and lift out the cartridge inside. Note the order the cartridges sit in so each one goes back in the same place. Set the O-rings aside where they will not roll away, and look inside each housing for sediment or discoloration. A cartridge that looks grey or feels slimy has reached the end of its use.
Wash the housings and replace cartridges
Wash each empty housing with mild dish soap and water, then rinse it until the soap is gone. Use white vinegar only if the manual allows it, and never mix cleaners. Fit a new cartridge where the old one was worn or dirty, following the schedule in the maker's manual. Put the O-rings back in place and check that each one sits flat in its groove.
Refit the housings and flush the system
Screw each housing back on by hand until it is snug, taking care not to cross the threads. Turn the water supply back on and plug the unit in again if it uses power. Open the faucet and let the water run to flush the system as the manual says, then check each housing for drips. If a housing leaks, close the supply, reseat the O-ring, and try again.
Use the system flushing feature
Some systems rinse the membrane for you. The Electrolux PureOne lets you start automatic membrane flushing through its app, which rinses the membrane to help reduce impurity buildup. Check the faucet display or the app for a filter status alert, and replace the cartridge when the alert asks.
What you need
As an Amazon Associate I earn from qualifying purchases. Product details come from each Amazon listing; we do not test products in person.
-
Electrolux PureOne 1200GPD Tankless Reverse Osmosis Under
Its single all-in-one filter has 12 stages of filtration, and the app schedules automatic membrane flushing to help reduce mineral buildup.
View on Amazon -
iSpring RCC7AK-BN NSF Certified
Its transparent first-stage housing lets you see buildup, and the system is certified to NSF/ANSI 58 with 6 stages of filtration.
View on Amazon -
Waterdrop G5P500A Reverse Osmosis System
Its 8-stage filtration is certified to NSF/ANSI 58 and 372, and it delivers 500 GPD with a tankless design.
View on Amazon -
APEC Water ROES-50
Its 5-stage system is certified to NSF/ANSI 58 and 372, and it uses quick connection fittings with colored tubing for service.
View on Amazon
These come from our ranked list Best Reverse Osmosis, which compares them spec by spec.
FAQ
Can I wash a reverse osmosis membrane with soap?
No. Wash only the empty filter housings with mild dish soap and water. The membrane itself is not washed; it is replaced when the manual says so, or flushed with the system's own flushing feature if it has one.
How often should I clean my reverse osmosis system?
Clean it when a filter looks grey, the flow slows, or the faucet display or app shows a filter alert. Follow the schedule in the maker's manual for cartridge changes, since the right interval depends on your incoming water.
What cleaners should I avoid on the filter housings?
Use only mild dish soap and water, white vinegar if the manual allows it, or the maker's own cleaner. Never mix cleaners, and never use pool or water-treatment chemicals in the housings.
Why is the water flow slow after cleaning?
Check that each cartridge sits in the right housing and that the O-rings sit flat, then flush the system as the manual says. If the flow stays slow after that, contact the maker or a repair service.




![[Dual Flow] Waterdrop WD-T4-A Alkaline pH+ Reverse](https://m.media-amazon.com/images/I/719YgI8NGvL._SL1500_.jpg)