How-to · Window Air Conditioners
How to Clean a Window AC Condenser
To clean the condenser on a window AC, unplug the unit, take out the filter, and clear leaves and dust from the fins at the back. Rinse the fins with a gentle stream of water, then let the unit dry before you put the filter back and plug it in. If the back of the unit sits where you cannot reach it, contact the maker or a repair service.
Unplug the unit and remove the filter
Unplug the window AC from the wall outlet before you touch any part of it. Open the front panel as the maker's manual shows and slide the filter out. Rinse the filter with water and a little mild dish soap only if the manual allows washing it, then let it dry fully before it goes back in. Set the filter aside while you clean the condenser so dust from the coil does not land on a clean filter.
Clear leaves and dust from the fins
The condenser sits at the back of the unit, facing outside. Pick leaves and loose debris off the fins by hand, then brush the fins with a soft brush to lift dust from between them. Work in the direction the fins run, and do not press hard against them. A vacuum with a brush attachment also lifts dust from the fins. If the back of the unit sits where you cannot reach it from inside, contact the maker or a repair service.
Rinse the fins with water
Rinse the condenser fins with a gentle stream of water from a hose or a jug, working from the top down so dirt runs off the bottom. Use water only, or a little mild dish soap if the manual allows it, and rinse again with water alone to take the soap off. Never use a pressure washer or spray cleaners into the unit, and never mix cleaners. Let the water drain out before you move on.
Let the unit dry and replace the filter
Leave the unit unplugged until the condenser feels dry to the touch. Running the fan mode for a while helps move air across the coil, so use it if your unit has one. Slide the dry filter back into place and close the front panel as the manual shows. Plug the unit back in and set it to cool. If water drips from the unit, unplug it and let it dry longer.
Know when to call a repair service
Stop and contact the maker or a repair service if the fins are bent, the coil leaks, or you find wiring and parts you do not recognize. Repairs inside the unit, including the compressor and refrigerant lines, are work for a repair service, not a cleaning job. Cleaning only helps when the condenser is dusty and the rest of the unit works as the manual describes. If the unit still cools poorly after cleaning, contact the maker or a repair service.
What you need
As an Amazon Associate I earn from qualifying purchases. Product details come from each Amazon listing; we do not test products in person.
-
GE Window Air Conditioner
Its washable, reusable slide-out filter lifts out for rinsing while you clean the condenser, and its mechanical dials give 2 cooling modes and 2 fan speeds.
View on Amazon -
Frigidaire 6,000 BTU Window Air Conditioner
Its washable dust filter can be rinsed, and Clean Filter alerts tell you when it is time to clean it.
View on Amazon -
ROVSUN 8000 BTU Window Air Conditioner
Its washable filter is reached from the front panel for regular cleaning, and its 5 modes include cool, heat, dry and fan.
View on Amazon -
Amazon Renewed Midea 5,000 BTU 150 Sq ft Mechanical
Its mechanical controls give 2 cooling modes and 2 fan speeds with seven temperature settings, and it fits windows 23 to 36 inches wide.
View on Amazon
These come from our ranked list Best Window AC Unit, which compares them spec by spec.
FAQ
How often should I clean the condenser?
Clean it when you see dust, leaves or debris on the fins, or when the air from the unit feels weaker than it did. Follow the cleaning schedule in the maker's manual, and clean the filter whenever you clean the condenser.
Can I clean the condenser from inside the room?
You can clean the filter and the front of the unit from inside. The condenser sits at the back, so clean it from outside the window, or contact the maker or a repair service if you cannot reach it.
What should I do if the fins are bent?
Stop and contact the maker or a repair service. Do not try to straighten the fins or open the unit, and do not touch wiring, the compressor or refrigerant lines.




