How-to · Robotic Pool Cleaners
How to Clean a Pool Vacuum Filter
To clean a pool vacuum filter, lift the cleaner out of the pool and switch it off, open the filter basket or compartment, and empty the trapped leaves and dirt into the trash. Rinse the filter with water and let it dry fully before it goes back in, and follow the maker's manual for your model.
Take the cleaner out of the pool
Switch the cleaner off and lift it out of the water. Set it on a flat surface near a hose or a bucket, with the filter side facing up. On a model with a plug-in power supply, unplug the power supply before you open the filter compartment. Let the cleaner drain for a moment so water does not run over your hands while you open it.
Empty the filter basket
Open the filter basket or compartment the way the maker's manual shows. Lift out the basket and tip the leaves, hair, sand and dirt into the trash, tapping the sides until the loose debris falls out. On a model with a top-load basket, the basket lifts straight out from the top. Check the compartment for debris left behind and pick it out by hand before you rinse.
Rinse the filter with water
Rinse the basket and the filter mesh under running water until the water runs clear. Use your fingers or a soft brush to work loose any sand or fine dirt caught in the mesh, and rinse the inside of the basket as well. If the manual allows it, a little mild dish soap can help with a greasy film; rinse it away fully before the filter goes back in. Do not use bleach or pool chemicals on the filter.
Dry the filter before it goes back
Shake off the extra water and set the basket and filter where air can reach them until they are fully dry. A filter that goes back in while still wet can hold dirt and give off a smell, so wait until the mesh feels dry to the touch. Put the basket back the way the manual shows and close the compartment. Check that the basket sits flat and the lid or cover clicks into place before the next run.
Know when the filter needs replacing
A filter that stays grey or torn after rinsing, or one that lets dirt through on the next run, needs replacing with the maker's own part. Follow the schedule in the maker's manual and replace the filter when the manual or the app asks. Keep a spare filter on hand so a worn filter does not sit in the cleaner while you wait for a new one.
What you need
As an Amazon Associate I earn from qualifying purchases. Product details come from each Amazon listing; we do not test products in person.
-
WYBOT C1 Cordless Robotic Pool Vacuum
A cordless cleaner with a 160-minute runtime and app control, which cleans the floor, walls, waterline and steps of inground pools.
View on Amazon -
AIPER Scuba V3 AI Vision Cordless Pool
A cordless cleaner with a multi-layer filtration system that pairs a 180 micron debris filter with a 3 micron layer, plus a wireless charging dock.
View on Amazon -
Dolphin Automatic Robotic Pool Vacuum Cleaner
A wall-climbing cleaner for in-ground pools up to 40 feet long, with a top-load filter basket and an active scrubbing brush.
View on Amazon -
(2026 Upgrade) Gosvor Pool Vacuum LiteVac G1
A cordless cleaner with app control and up to 200 minutes of runtime, whose double filtration and 3.6L top-load filter basket capture 3-micron debris.
View on Amazon
These come from our ranked list Best Pool Vacuum, which compares them spec by spec.
FAQ
Can I rinse a pool vacuum filter with a hose?
Yes, if the manual allows it. Rinse the basket and the filter mesh with water until the water runs clear, and let the filter dry fully before it goes back in the cleaner.
How often should I clean a pool vacuum filter?
Clean it when it looks dirty or grey, when the cleaner leaves dirt behind, or when the app or the manual asks. Follow the schedule in the maker's manual for your model.
Can I use soap on a pool vacuum filter?
Only a little mild dish soap, and only if the manual allows it. Rinse the soap away fully before the filter goes back in, and never use bleach or pool chemicals on it.





