How-to · Tankless Water Heaters
How Tankless Water Heaters Work
When you open a hot tap, cold water flows through a heat exchanger, and a gas burner heats it as it passes, so hot water reaches the tap on demand. The heater fires only while water flows, and it stops when the tap closes. Flow rate in gallons per minute decides how many taps it can feed at once.
Cold water flows in, hot water flows out
A tankless heater works on flow, not storage. Opening a hot tap sends cold water into the unit, where a sensor starts the burner and the water picks up heat as it moves through the heat exchanger. The water leaves the unit hot and runs straight to the tap, so there is no tank of hot water waiting and no tank to empty. When the tap closes, the burner stops. The MIZUDO starts at a flow as low as 0.53 GPM, so a single low-flow tap can still call for hot water.
Flow rate decides how many taps run at once
Flow rate, given in gallons per minute, is the figure to compare. The Rheem delivers 7.0 GPM and covers 2 to 3 simultaneous showers, and the Westinghouse delivers 7.9 GPM for 3 to 5 fixtures. The Rinnai delivers 10 GPM for 6 fixtures at once, and the MIZUDO delivers 10.3 GPM across 5 to 7 outlets. Count the taps, showers and appliances that may run at the same time, then match that count to the flow rate the maker gives.
Gas, condensing and venting
Three of the units here run on natural gas, and the Westinghouse runs on propane, while the Rinnai runs on natural gas or propane. The Rinnai is a condensing unit, and the Rheem and Westinghouse are non-condensing units. The Rheem uses a direct vent system, and the MIZUDO uses a sealed concentric direct-vent system that draws outdoor air for combustion. Gas, venting and mounting are installer work: follow the maker's installation manual and use a licensed installer where the manual says so.
Controls, upkeep and the manual
The Rheem has a digital LED temperature control panel with precision adjustments of plus or minus 1 degree. The Rinnai has an easy-to-use interface and a Quick Flush feature for flushing. Follow the manual for flushing and descaling, and contact the maker or a repair service for work inside the unit.
What you need
As an Amazon Associate I earn from qualifying purchases. Product details come from each Amazon listing; we do not test products in person.
-
Rheem RTG Series 7.0 GPM Natural Gas
A 7.0 GPM natural gas unit with 160,000 BTU, a digital LED temperature panel, freeze protection and LeakGuard leak detection.
View on Amazon -
MIZUDO Natural Gas Tankless Water Heater
A 10.3 GPM natural gas unit with 199,000 BTU, WiFi and app control, and a 0.53 GPM low-flow activation.
View on Amazon -
Rinnai RX180iN Condensing Smart Sense Tankless Water
A 10 GPM condensing unit that runs on natural gas or propane, with a Quick Flush feature and an easy-to-use interface.
View on Amazon -
Westinghouse Tankless Water Heater Propane Indoor
A 7.9 GPM propane unit with 180,000 BTU, app and voice control, and a copper heat exchanger.
View on Amazon
These come from our ranked list Best Tankless Water Heater, which compares them spec by spec.
FAQ
Do tankless water heaters run out of hot water?
No. They heat water as it flows, so there is no stored tank to empty. The flow rate still limits how many taps can run at once, so match the gallons per minute to your home.
What flow rate do I need for my home?
Compare the gallons per minute with the taps that may run together. The Rheem covers 2 to 3 showers at 7.0 GPM, and the MIZUDO covers 5 to 7 outlets at 10.3 GPM.
Do tankless water heaters need a gas line?
The units here run on natural gas or propane, and they need a gas supply and venting. Follow the maker's installation manual and use a licensed installer where the manual says so.




