How-to · Well Pumps
How a Well Pump Pressure Switch Works
A well pump pressure switch watches the pressure in your water line and turns the pump on and off. When you open a tap and the pressure falls, the switch closes its contacts and the pump starts. When the pressure rises to the shut-off point, the switch opens the contacts and the pump stops.
What the switch watches
The switch sits on the water line near the pressure tank and reads the pressure in the system. Inside, water pressure pushes against a diaphragm while a spring pushes back. When the pressure falls, the spring wins and the contacts close. When the pressure rises, the water pushes the diaphragm back and the contacts open. The switch only reads pressure; it does not move water itself.
How the pump starts
Open a tap and water leaves the tank, so the pressure in the line falls. At the cut-in point the switch closes its contacts and sends power to the pump, and the pump starts moving water into the tank and the house. The Acquaer Shallow/Deep Well Jet Pump has an automatic pressure switch that starts the pump when the pressure falls below 20 PSI.
How the pump stops
With the taps closed, the pump keeps filling the tank and the pressure climbs. At the cut-out point the switch opens its contacts and the pump stops. The Acquaer Shallow/Deep Well Jet Pump shuts the pump off when the pressure rises over 40 PSI. Between the two points the switch holds the pump off until use drops the pressure again.
What the pressure tank adds
The tank holds a store of water under pressure, so short uses like a quick rinse draw from the tank instead of starting the pump each time. The switch reads the tank pressure, so the pump runs in longer stretches with rests in between. A tank that holds little water makes the pump start and stop often, which is a sign to check the tank and the switch settings in the maker's manual.
When the switch needs a look
A pump that starts and stops in short bursts, a pump that will not start, or taps with no water can point to the switch or the tank. Check the manual for the checks it lists and the settings it gives. For wiring or a switch replacement, follow the maker's installation manual and hire a licensed electrician where the manual says so. Do not open the switch or the pump housing.
What you need
As an Amazon Associate I earn from qualifying purchases. Product details come from each Amazon listing; we do not test products in person.
-
VEVOR Deep Well Submersible Pump 1 HP
A 1 HP submersible pump with 37 GPM max flow and 207 ft max head, with a built-in check valve to prevent back-flow.
View on Amazon -
CrestWave 1 HP Shallow/Deep Well Jet Pump
A 1 HP convertible jet pump with 2,330 GPH max flow and 145 ft max lift, for wells to 26 ft or 90 ft with the ejector kit.
View on Amazon -
Acquaer Shallow/Deep Well Jet Pump
A 1 HP convertible jet pump with an automatic pressure switch that starts the pump below 20 PSI and shuts it off over 40 PSI.
View on Amazon -
Hallmark Industries MA0414X-7 Deep Well Submersible Pump
A 1 HP deep well submersible pump with 33 GPM max flow, a 3.8-inch max outside diameter and a 1-year warranty.
View on Amazon
These come from our ranked list Best Well Pump, which compares them spec by spec.
FAQ
Why does my well pump turn on and off so often?
The switch starts the pump when the pressure falls and stops it when the pressure rises, so short bursts can mean the tank holds little water or the switch settings need a look. Check the maker's manual for the checks it lists.
What pressure does a well pump pressure switch use?
It depends on the switch. The Acquaer Shallow/Deep Well Jet Pump starts its pump when the pressure falls below 20 PSI and shuts it off over 40 PSI. Check your switch and manual for the points your setup uses.
Can I adjust a well pump pressure switch myself?
Follow the maker's manual for the settings it gives and the checks it lists. For wiring or a switch replacement, hire a licensed electrician where the manual says so.



